Linux下用dnsmasq做dns cache server的配置方法__dnsmasq_keepalived_etc_conf_resolv_

当前位置: 操作系统/服务器>linux

Linux下用dnsmasq做dns cache server的配置方法

来源: 互联网发布时间：2014-08-25

本文导语: 目前最新版是2.7.1 ，可去其FTP下载：http://www.thekelleys.org.uk/dnsmasq/ 安装过程比较简单 yum -y install dnsmasq* wget http://www.keepalived.org/software/keepalived-1.2.9.tar.gz tar zxvf keepalived-1.2.9.tar.gz cd keepalived-1.2.9 ./configure --prefix=/usr/local/keepal...

目前最新版是2.7.1 ，可去其FTP下载：http://www.thekelleys.org.uk/dnsmasq/

安装过程比较简单

yum -y install dnsmasq* 
wget http://www.keepalived.org/software/keepalived-1.2.9.tar.gz
tar zxvf keepalived-1.2.9.tar.gz
cd keepalived-1.2.9
./configure --prefix=/usr/local/keepalived
make && make install
mkdir /etc/keepalived
cp /usr/local/keepalived/etc/keepalived/keepalived.conf /etc/keepalived/
ln -s /usr/local/keepalived/etc/sysconfig/keepalived /etc/sysconfig/
ln -s /usr/local/keepalived/etc/rc.d/init.d/keepalived /etc/init.d/
ln -s /usr/local/keepalived/sbin/keepalived /usr/sbin/
chkconfig --add keepalived
chkconfig --level 35 keepalived on

keepalived的配置很简单，只需要配置一个VIP可以在两台Server之间飘来飘去就可以实现主备了

! Configuration File for keepalived
 
global_defs {
  notification_email {
   xxx@xxx.com
  }
  notification_email_from xxx@xxx.com
  smtp_server 127.0.0.1
  smtp_connect_timeout 30
  router_id LVS_DEVEL
}
 
vrrp_instance dnscache {
  state MASTER         // 另一台配置BACKUP
  interface eth1        // 在哪个接口上进行服务器状态检测
  virtual_router_id 51
  priority 180         // BACKUP机器上配置100
  advert_int 1         // 检查间隔，单位为秒
  authentication {
    auth_type PASS
    auth_pass 1234
  }
 
  virtual_ipaddress {       // VIP设置，指定到内网网卡 
    192.168.100.99/24 dev eth1
  }
}

dnsmasq的配置也很简单

resolv-file=/etc/resolv.dnsmasq.conf
cache-size=1000
conf-dir=/etc/dnsmasq.d

　　将dns地址写入到/etc/resolv.dnsmasq.conf文件中

echo "nameserver 8.8.8.8" > /etc/resolv.dnsmasq.conf

　　本机和局域网其它全部的服务器dns解析都用它

echo "nameserver 192.168.100.99" > /etc/resolv.conf

　　最后找一台局域网Server验证一下，如果能解析就说明正常了.

nslookup www.google.cn 192.168.100.99

　　此方案只适合小型企业，规模少的情况下使用，解析量大的时候还是用bind最好。

下面是其它网友的补充：

代码如下:

sudo pacman -S --needed dnsmasq
cd /etc

[admin@huangye etc]$ sudo cp -v dnsmasq.conf{,.orig}
`dnsmasq.conf' -> `dnsmasq.conf.orig'

[admin@huangye etc]$ sudo vim dnsmasq.conf

相比来说，dnsmasq的配置简单多了：

代码如下:

resolv-file=/etc/dnsmasq.resolv.conf

addn-hosts=/etc/dnsmasq.hosts

local=/localnet/

no-dhcp-interface=eth0

conf-dir=/etc/dnsmasq.d

代码如下:

[admin@huangye etc]$ sudo cp -v resolv.conf dnsmasq.resolv.conf
Password:
`resolv.conf' -> `dnsmasq.resolv.conf'
sudo mkdir /etc/dnsmasq.d
sudo touch /etc/dnsmasq.hosts

sudo /etc/rc.d/dnsmasq start

最后，别忘记加入rc.conf DAEMONS,注意要在network后面。

dnsmasq 可从额外的hosts文件读取条目，如可以这样添加正向解析：

echo "IP地址域名" > /etc/dnsmasq.hosts

另外，重启dnsmasq可以用SIGHUP（可以在修改hosts文件后，让配置生效）

killall -s SIGHUP dnsmasq

查看服务状态：

netstat -tunl
tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN
udp 0 0 0.0.0.0:53 0.0.0.0:*

再dig 一下，发现稳定在4ms ,我晕，同样的配置，我在一台ubuntu server 10.04 上面dig 是1ms ,在我本地居然在4ms ,囧