当前位置: 技术问答>linux和unix
我刚装上mandrake9.2,不知该怎么设置ADSL请指教
来源: 互联网 发布时间:2015-05-20
本文导语: 多谢,越具体越好。 | 图形模式上网: 1. 最好的ADSL拨号工具当然是rp-pppoe。它本身是一个协议,又是一个拨号配置工具。 2. 用urpmi rp-pppoe-gui 安装(同时会自动装上rp-pppoe)。 3. 如果是采...
多谢,越具体越好。
|
图形模式上网:
1. 最好的ADSL拨号工具当然是rp-pppoe。它本身是一个协议,又是一个拨号配置工具。
2. 用urpmi rp-pppoe-gui 安装(同时会自动装上rp-pppoe)。
3. 如果是采用幸福的包月方式,那么直接用adsl-setup配置,起动就会自动拨号。什么都不用管。(问到DNS时,键入小写的 server )
4. 如果要用图形界面的拨号工具,那就是用 tkpppoe 命令,先用root配置好,并允许普通用户使用。非常方便。
5. 如果是象我一样用的是计时的,那就不能一起动就自动拨号。怎么办?当然是
drakxservices 程序。 打开以后,你一看就明白了。
6. 然后,等你要上网了,就用tkpppoe(起动菜单中有)一点鼠标。这个程序还有流量显示的。
字符模式下:
这样来试一下,要先设置网卡
#netconf
把IP和DNS设置成如下的。
IP地址:192.168.0.1
掩码:
255.255.255.0
DNS
202.96.134.133
202.96.168.68
不要设置网关
然后再来设置ADSL。这一处,我们要用命令。
#adsl-setup
Welcome to the Roaring Penguin ADSL client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Looks good! Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名
INTERFACE
>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):如果一张网卡就设置写上eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):不用写什么
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:在这里写上202.96.134.133
下一个DNS是202.96.168.68
PASSWORD
>>> Please enter your PPPoE password:输入密码
>>> Please re-enter your PPPoE password:再输入一次
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2):这里添写为2
** Summary of what you entered **
Ethernet Interface: eth0
User name: XXX
Activate-on-demand: No
DNS: Do not adjust
Firewalling: MASQUERADE
>>> Accept these settings and adjust configuration files (y/n)?
弄完后,就按一个y键。
用adsl-start来启动ADSL。如果不成功就重启一下计算机。
如果再不成功呢????要发以下文件的内容:
/etc/sysconfig/network-scripts/ifcfg-eth0
/etc/ppp/pppoe.conf
/etc/resolv.conf
/etc/sysconfig/network-scripts/net_cnx_up
1. 最好的ADSL拨号工具当然是rp-pppoe。它本身是一个协议,又是一个拨号配置工具。
2. 用urpmi rp-pppoe-gui 安装(同时会自动装上rp-pppoe)。
3. 如果是采用幸福的包月方式,那么直接用adsl-setup配置,起动就会自动拨号。什么都不用管。(问到DNS时,键入小写的 server )
4. 如果要用图形界面的拨号工具,那就是用 tkpppoe 命令,先用root配置好,并允许普通用户使用。非常方便。
5. 如果是象我一样用的是计时的,那就不能一起动就自动拨号。怎么办?当然是
drakxservices 程序。 打开以后,你一看就明白了。
6. 然后,等你要上网了,就用tkpppoe(起动菜单中有)一点鼠标。这个程序还有流量显示的。
字符模式下:
这样来试一下,要先设置网卡
#netconf
把IP和DNS设置成如下的。
IP地址:192.168.0.1
掩码:
255.255.255.0
DNS
202.96.134.133
202.96.168.68
不要设置网关
然后再来设置ADSL。这一处,我们要用命令。
#adsl-setup
Welcome to the Roaring Penguin ADSL client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Looks good! Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名
INTERFACE
>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):如果一张网卡就设置写上eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):不用写什么
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:在这里写上202.96.134.133
下一个DNS是202.96.168.68
PASSWORD
>>> Please enter your PPPoE password:输入密码
>>> Please re-enter your PPPoE password:再输入一次
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2):这里添写为2
** Summary of what you entered **
Ethernet Interface: eth0
User name: XXX
Activate-on-demand: No
DNS: Do not adjust
Firewalling: MASQUERADE
>>> Accept these settings and adjust configuration files (y/n)?
弄完后,就按一个y键。
用adsl-start来启动ADSL。如果不成功就重启一下计算机。
如果再不成功呢????要发以下文件的内容:
/etc/sysconfig/network-scripts/ifcfg-eth0
/etc/ppp/pppoe.conf
/etc/resolv.conf
/etc/sysconfig/network-scripts/net_cnx_up